New to Home Brew - quick question

[TheWizard]

hello everyone,

basic question on home brewing. To make sure you have the correct dosage, in essence, if i have 50g of test E, and want to make 250mg/ml from it, it should make 200ml, i need to use .18% BB .02% BA add the test raw material then top off with oil until i get 200ml total?

ive been trying the calculator on Basskilleronline here--> http://basskilleronline.com/steroid-powder-calculator.html
but it has a variable block im not 100% sure on, the powder weight. i believe it is the liquid amount of 1g of powder/gel once warmed they melt giving a liquid volume. im pretty sure thats what goes in that block.

i just want to make sure im dosing correctly. any comments and discussion would be great.
thanks in advance.

 

[motivator360]

hello everyone,

basic question on home brewing. To make sure you have the correct dosage, in essence, if i have 50g of test E, and want to make 250mg/ml from it, it should make 200ml, i need to use .18% BB .02% BA add the test raw material then top off with oil until i get 200ml total?

ive been trying the calculator on Basskilleronline here--> http://basskilleronline.com/steroid-powder-calculator.html
but it has a variable block im not 100% sure on, the powder weight. i believe it is the liquid amount of 1g of powder/gel once warmed they melt giving a liquid volume. im pretty sure thats what goes in that block.

i just want to make sure im dosing correctly. any comments and discussion would be great.
thanks in advance.

...let's say you fill up a glass of water to almost the rim of the glass...then you start putting scoop after scoop of ice tea mix into the glass...you will notice the more ice tea mix you put in the glass the level of liquid will rise as well...this is the displacement factor that basskillers sets for you...

1 gram of Test E raw powder displaces .943ml of oil...so to make 200ml of Test E dosed @250mg...with BA@2% & BB@18%...you'll need 112.85ml of carrier oil...4ml of BA ...36ml of BB


Sent from my iPhone using Tapatalk

 

[npnutrition]

I wish I've had a mentor like you, learn about this in the hard way, even though it doesn't affect too much, but it's more accurate this way.


Enviado desde mi iPhone utilizando Tapatalk

 

[TheWizard]

...let's say you fill up a glass of water to almost the rim of the glass...then you start putting scoop after scoop of ice tea mix into the glass...you will notice the more ice tea mix you put in the glass the level of liquid will rise as well...this is the displacement factor that basskillers sets for you...

1 gram of Test E raw powder displaces .943ml of oil...so to make 200ml of Test E dosed @250mg...with BA@2% & BB@18%...you'll need 112.85ml of carrier oil...4ml of BA ...36ml of BB Sent from my iPhone using Tapatalk

thats pretty much exactly what i needed to confirm, they dont list all products displacement weights so i assume id have to liquefy some of them and figure that myself, like how many ML of liquid 100g of a certain powder/gel liquefies to?

 

[TheWizard]

yea, i want to be correct with the dosage

 

[npnutrition]

In the basskiller's page there's a list of the most common raw's displacements


Enviado desde mi iPhone utilizando Tapatalk

 

[motivator360]

thats pretty much exactly what i needed to confirm, they dont list all products displacement weights so i assume id have to liquefy some of them and figure that myself, like how many ML of liquid 100g of a certain powder/gel liquefies to?

Yea I guess I'd round them down then use the top-off method..better to be under your target ml's than over..that will just mean your product will be stronger rather than weaker..


Sent from my iPhone using Tapatalk

 

[Pez]

hello everyone,

basic question on home brewing. To make sure you have the correct dosage, in essence, if i have 50g of test E, and want to make 250mg/ml from it, it should make 200ml, i need to use .18% BB .02% BA add the test raw material then top off with oil until i get 200ml total?

ive been trying the calculator on Basskilleronline here--> http://basskilleronline.com/steroid-powder-calculator.html
but it has a variable block im not 100% sure on, the powder weight. i believe it is the liquid amount of 1g of powder/gel once warmed they melt giving a liquid volume. im pretty sure thats what goes in that block.

i just want to make sure im dosing correctly. any comments and discussion would be great.
thanks in advance.

Test Enan is for all is can remember 0.91-0.92 (density). Just remember this, get a non sterile glass vial or even a 10ml graduated cylinder and see where you get after adding the BA/BB to the raw material and heat it. That tells you more than anything. If hand filtering remember how much oil/fluid medium it takes to 'purge' the filter. I'd look for some syringe pre-filters (I see nylon 1 micron ones that come out to be about 70 cents). The downer is they come in a pack of 100. What is your total volume you wish to end up with? Syringe filtering,even with using a veterinary syringe fall short 95% of the time. If you used EO or much thinner carrier the closer you can come to 100ml for a 25mm syringe filter.